When an Error Message is Displayed
- Check the error code and error code number displayed on the operation panel.
List of Error Codes
No Card
- Cards have run out.
Replenish the cards.
- The card hopper is not installed.
Install the card hopper.
Memo
The operation panel display appears blinking when the cards have run out or when the card hopper is not installed.
Close
Jam(Hopper) 90
- Card jam near the card hopper and cleaning roller.
Remove the jammed card.
Jam(TurnOver) 91
- Card jam near the card turn over unit.
Remove the jammed card.
Jam(MG) 92
- Card jam in the magnetic encoder unit.
Remove the jammed card.
Jam(Transfer) 93
- Card jam in the card feed roller.
Remove the jammed card.
Jam(Discharge) 94
- Card jam near the card outlet.
Remove the jammed card.
Jam(Retran.) 95
- Card jam near the retransfer heating roller.
Remove the jammed card.
Film Search A1
- Retransfer film is broken.
Repair the retransfer film.
MG Test Err A8
- A writing error has occurred during magnetic encoder self-diagnosis.
Press
to reset the printer.
Ink Error B0
- An incorrect ink ribbon is installed.
Install a correct ink ribbon.
Ink Search B1
- Ink ribbon is broken.
Repair the ink ribbon.
Door Open D1
- The printer door is open.
Close the printer door, and press to reset the printer.
- Cleaning unit is not installed.
Install the cleaning unit, close the printer door, and press to reset the printer.
Memo
The operation panel display appears blinking when the printer door is open or when the cleaning unit is not installed.
Close
Film Run Out A2
- Retransfer film has run out.
Replace with a new one.
Ink Run Out B2
- Ink ribbon has run out.
Replace with a new one.
Hardware 44
- A hardware failure has occurred on the printer.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
MG Mechanical AB
- An error has occurred in the mechanical component of the magnetic encoder.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
MG Hardware AC
- A hardware failure has occurred on the magnetic encoder.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
Cam Error C1
- A heating roller operation error has occurred.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
HR Overheat C2
- The temperature of the bend remedy heating roller or retransfer heating roller is too high.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
Hardware D8
- A hardware error has occurred during initialization.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
TR Overheat F0
- The temperature of the retransfer heating roller is too high.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
TR Heater F1
- The retransfer heating roller is faulty.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
TR Thermister F2
- The retransfer heating roller thermistor is faulty.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
RR Overheat F3
- The temperature of the bend remedy heating roller is too high.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
RR Heater F4
- The bend remedy unit is faulty.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
RR Thermister F5
- The bend remedy heating roller thermistor is faulty.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
Overcool F6
- The operating ambient temperature of the printer is too low.
Check the temperature. If the same problem recurs within the range of operating ambient temperature, turn off the power and consult our authorized dealers.
Head Overheat F8
- The temperature of the thermal head is too high.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
Power Intrpt C3
- An instantaneous interruption is detected.
Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers.
Close